Cateye silverado seat console conversion kit11/21/2023 ![]() ![]() The front and rear suspension systems are independent, while the front and rear brake systems are ventilated. The 2022 Chevy Tahoe SUV’s suspension features a ventilated disc brake system. Its steering wheel controls include audio, call, multimedia, and cruise control switches. This Chevy SUV has an electric power steering (EPS) system. At the same time, its torque delivers 518 Newton meters (Nm) at 4,100 rpm. Its output is 355 horsepower (hp) at 5,600 revolutions per minute (rpm). The 2022 Chevy Tahoe is powered by a 5.3-liter Gas EcoTec3 V8 engine featuring the Dynamic Fuel Management System with Direct Injection. Let’s take a look at the specs of the 2022 Chevrolet Tahoe based on the following categories: Around this time, some Chevy Tahoe owners started converting their SUV’s headlights to Cateye headlights. The popularity of the Chevy Silverado Cateye started as soon as it was initially launched in 2003. News & World Report as the number one Affordable Large SUV. In 2014, it was even recognized by the U.S. The Chevy Tahoe SUV has consistently been recognized as one of the best-selling, if not the best, full-size sport utility vehicles in the United States. The name “Tahoe” was derived from Lake Tahoe, which is a large rugged, and scenic freshwater lake located in the Sierra Nevada of the United States. Its counterpart, which is referred to as GMC Yukon, has been around since 1991. The Chevrolet Tahoe is a full-size sport utility vehicle (SUV) produced by General Motors Co. The conversion of the Chevy Tahoe headlights to Cat Eye headlights is one of the popular ones. Since its launch, Cateye headlights have become so famous that some Chevy truck owners opted to install them on their trucks. The headlights of this model resemble a cat’s eyes, explaining the model’s name. Cat Eye Tahoe Conversion, Tips, GuideĪ Cateye is one of the Chevy Silverado models manufactured between 20. Read more about the Cateye Tahoe conversion and the Chevy Tahoe SUV. ![]() Since its initial launch, Cateye headlights have become so popular that some Chevy truck owners chose to install them on their trucks. ![]() Its headlights resemble the eyes of a cat, which explains the name. So, what is Cateye Tahoe conversion?Ī Cateye refers to a Chevy Silverado model produced between 20. While not all Chevy vehicles have cat eyes, some Chevy truck owners have converted theirs to have these. My mounts include some offset holes for Corbeau seats on most brackets but other brands will be centered on the bracket.If you are a Chevy enthusiast, you are most likely familiar with the Cateye. With aftermarket seats that fit more snuggly this will be more obvious, but it is not an issue. This is not obvious while driving or unless you are looking for it with stock seats. Note: Just about every car or truck made in the last 30 years has the steering wheel and seat slightly offset. There is an extra charge for custom siding and additional wait time (usually 2-3 weeks) due to having them designed and cut. The outside face is available with the AFP logo with slots on either side, the LSX logo, or a Custom siding which can be whatever you want. The brackets can be ordered in Driver Side Only, or Both Seats. The GMT900 brackets are 6.5″ in the front and 5″ in the rear for a 6 degree layback angle (same as factory). Layback angle is approximately 7 degrees and the GMT800 front is 6″ off the floor and rear is 4″ off the floor (factory seat height). These will work with the Corbeau or Braum slider rails as well. ![]() There are multiple seat mounting positions to position the seat up to 3″ forward and back and 1.5″ left or right (expect on GMT400 brackets). They will accommodate a center console and drop directly on to the factory floor bolt pattern, no trimming or drilling is required. The passenger side weighs approximately 12.75 pounds and the driver side weighs approximately 13.0 pounds for the GMT800 and GMT900 brackets, and slightly less for the GMT400 brackets. They can be easily powder coated at your leisure (I do not offer powder coating service on these). Brackets will ship raw ready for your paint or powdercoat. Harness mounting holes are 1/2″ in diameter. There are holes to mount a 3, 4, 5, or 6 point harness directly to the brackets without the need for a roll cage (this is NOT a replacement for a roll cage!). These are laser cut from 3/16″ steel and are fully MIG welded with support gussets for strength. They are intended for Corbeau, Sparco, or Braum seats but can work with other seats as well (Kirkeys, etc.). These seat brackets are made to install aftermarket seats on the factory floor bolts in 1988-2018 GMT400, GMT800, GMT900, and GM2kxx GM Trucks (Silverado, Sierra, Tahoe, Suburban, Denali, Escalade, Yukon, etc.). ![]()
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |